I have a Netgate SG-3100 running pfSense 2.4.4-p2.
LAN IP subnet is 10.5.1.1/24, and DHCP range is 10.5.1.10 to 10.5.1.245.
I'm trying to set this up with a Ruckus ICX-7150-C12P switch running FastIron 08.0.90a (routing image). I just upgraded this today, and did a factory reset. I've configured an IP address on Ethernet port 1, but otherwise it should be pretty much factory defaults.
ICX7150-C12 Router>show running-config Current configuration: ! ver 08.0.90aT213 ! stack unit 1 module 1 icx7150-c12-poe-port-management-module module 2 icx7150-2-copper-port-2g-module module 3 icx7150-2-sfp-plus-port-20g-module stack-port 1/3/1 stack-port 1/3/2 ! aaa authentication web-server default local aaa authentication login default local enable aaa console ! no telnet server username super password ..... ! sz registrar ! interface ethernet 1/1/1 ip address 10.5.1.5 255.255.255.0 ! interface ethernet 1/3/1 speed-duplex 1000-full ! interface ethernet 1/3/2 speed-duplex 1000-full ! ip ssh idle-time 5 ! end
I then connect port 1 on the Ruckus 7150 to one of the LAN ports on the SG-3100. It comes up briefly, I can ping it:
ICX7150-C12 Router>show interfaces ethernet 1/1/1 GigabitEthernet1/1/1 is up, line protocol is up Port up for 14 second(s) Hardware is GigabitEthernet, address is d4c1.9e88.f6d2 (bia d4c1.9e88.f6d2) Configured speed auto, actual 1Gbit, configured duplex fdx, actual fdx Configured mdi mode AUTO, actual MDI Untagged member of L2 VLAN 1, port state is FORWARDING BPDU guard is Disabled, ROOT protect is Disabled, Designated protect is Disabled Link Error Dampening is Disabled STP configured to ON, priority is level0, mac-learning is enabled Openflow is Disabled, Openflow Hybrid mode is Disabled, Flow Control is config enabled, oper enabled, negotiation disabled Mirror disabled, Monitor disabled Mac-notification is disabled VLAN-Mapping is disabled Not member of any active trunks Not member of any configured trunks No port name IPG MII 0 bits-time, IPG GMII 0 bits-time Internet address is 10.5.1.5/24, MTU 1500 bytes, encapsulation ethernet MMU Mode is Store-and-forward 300 second input rate: 7952 bits/sec, 3 packets/sec, 0.00% utilization 300 second output rate: 144 bits/sec, 0 packets/sec, 0.00% utilization 323 packets input, 86733 bytes, 0 no buffer Received 16 broadcasts, 301 multicasts, 6 unicasts 0 input errors, 0 CRC, 0 frame, 0 ignored 0 runts, 0 giants 27 packets output, 3227 bytes, 0 underruns Transmitted 10 broadcasts, 13 multicasts, 4 unicasts 0 output errors, 0 collisions Relay Agent Information option: Disabled Protected: No MAC Port Security: Disabled This port is not being monitored for queue drops Egress queues: Queue counters Queued packets Dropped Packets 0 0 0 1 0 0 2 0 0 3 0 0 4 0 0 5 14 0 6 0 0 7 13 0
Then after about 2 minutes, the port inexplicably goes down:
ICX7150-C12 Router>show interfaces ethernet 1/1/1 GigabitEthernet1/1/1 is down, line protocol is down Port down for 8 minute(s) 45 second(s) Hardware is GigabitEthernet, address is d4c1.9e88.f6d2 (bia d4c1.9e88.f6d2) Configured speed auto, actual unknown, configured duplex fdx, actual unknown Configured mdi mode AUTO, actual unknown Untagged member of L2 VLAN 1, port state is BLOCKING BPDU guard is Disabled, ROOT protect is Disabled, Designated protect is Disabled Link Error Dampening is Disabled STP configured to ON, priority is level0, mac-learning is enabled Openflow is Disabled, Openflow Hybrid mode is Disabled, Flow Control is config enabled, oper enabled, negotiation disabled Mirror disabled, Monitor disabled Mac-notification is disabled VLAN-Mapping is disabled Not member of any active trunks Not member of any configured trunks No port name IPG MII 0 bits-time, IPG GMII 0 bits-time Internet address is 10.5.1.5/24, MTU 1500 bytes, encapsulation ethernet MMU Mode is Store-and-forward 300 second input rate: 0 bits/sec, 0 packets/sec, 0.00% utilization 300 second output rate: 0 bits/sec, 0 packets/sec, 0.00% utilization 250 packets input, 66752 bytes, 0 no buffer Received 6 broadcasts, 238 multicasts, 6 unicasts 0 input errors, 0 CRC, 0 frame, 0 ignored 0 runts, 0 giants 20 packets output, 2272 bytes, 0 underruns Transmitted 8 broadcasts, 8 multicasts, 4 unicasts 0 output errors, 0 collisions Relay Agent Information option: Disabled Protected: No MAC Port Security: Disabled This port is not being monitored for queue drops Egress queues: Queue counters Queued packets Dropped Packets 0 0 0 1 0 0 2 0 0 3 0 0 4 0 0 5 12 0 6 0 0 7 8 0
Logging:
ICX7150-C12 Router>show logging Syslog logging: enabled ( 0 messages dropped, 0 flushes, 0 overruns) Buffer logging: level ACDMEINW, 34 messages logged level code: A=alert C=critical D=debugging M=emergency E=error I=informational N=notification W=warning Static Log Buffer: Jan 1 00:04:23:I:System: Stack unit 1 POE PS 1, Internal Power supply with 124000 mwatts capacity is up Dynamic Log Buffer (4000 lines): Jan 1 00:26:39:I:System: Interface ethernet 1/1/1, state down Jan 1 00:26:17:I:System: PoE: Power disabled on port 1/1/1 because of detection of non-PD. PD detection will be disabled on port. Jan 1 00:26:16:I:System: Interface ethernet 1/1/1, state up Jan 1 00:26:12:I:System: Interface ethernet 1/1/1, state down Jan 1 00:24:31:I:System: PoE: Power disabled on port 1/1/1 because of detection of non-PD. PD detection will be disabled on port. Jan 1 00:24:30:I:System: Interface ethernet 1/1/1, state up Jan 1 00:14:56:I:System: Interface ethernet 1/1/1, state down Jan 1 00:14:30:I:System: PoE: Power disabled on port 1/1/1 because of detection of non-PD. PD detection will be disabled on port. Jan 1 00:14:29:I:System: Interface ethernet 1/1/1, state up Jan 1 00:14:18:I:System: Interface ethernet 1/1/1, state down Jan 1 00:14:18:I:System: PoE: Power disabled on port 1/1/1 because of detection of non-PD. PD detection will be disabled on port. Jan 1 00:14:17:I:System: Interface ethernet 1/1/1, state up Jan 1 00:13:52:I:Security: console logout by super from PRIVILEGED EXEC mode Jan 1 00:13:51:I:Security: running-config was potentially changed by super from console Jan 1 00:11:49:I:System: Interface ethernet 1/1/1, state down Jan 1 00:11:36:I:System: PoE: Power disabled on port 1/1/1 because of detection of non-PD. PD detection will be disabled on port. Jan 1 00:11:35:I:System: Interface ethernet 1/1/1, state up Jan 1 00:10:24:I:COPY COMPLETED Jan 1 00:10:24:I:Security: startup-config was changed by super from console Jan 1 00:10:24:I:COPY_CONFIGURATION_TO_FLASH Jan 1 00:10:04:I:PORT: 1/1/1, added ip address 10.5.1.5 by super from console session. Jan 1 00:09:29:I:Security: console login by super to PRIVILEGED EXEC mode Jan 1 00:09:28:I:Security: console logout by super from PRIVILEGED EXEC mode Jan 1 00:09:26:I:Security: running-config was potentially changed by super from console Jan 1 00:07:21:I:Security: console login by super to PRIVILEGED EXEC mode Jan 1 00:05:47:I:Security: user super modified by super from console session. Jan 1 00:05:13:I:Security: console login by super to USER EXEC mode Jan 1 00:05:09:I:Security: Console login by user super failed Jan 1 00:04:36:I:Security: server (RSA) enabled by un-authenticated user from console session. Jan 1 00:04:23:I:System: Stack unit 1 POE PS 1, Internal Power supply with 124000 mwatts capacity is up Jan 1 00:04:20:I:PKI: Trustpoint DEVICE_TRUSTPNT: Successfully loaded Manufacturing certificate file. Jan 1 00:04:19:I:System: Warm start Jan 1 00:04:19:A:WARNING: FI image is not booted from UFI, download UFI and reboot system for full functionality Jan 1 00:04:19:D:DHCPC: starting dhcp client service on 656 port(s)
Any ideas what's going on?
UPDATE: Hmm, it might be something to do with my having assigned an IP address to port 1?
If I remove that, the port stays up.
UPDATE 2: I then plugged port 3 on the switch into pfSense.
It somehow seemed to dynamically take an IP address?
interface ethernet 1/1/3 ip address 10.5.1.27 255.255.255.0 dynamic
No comments:
Post a Comment